If you read the FrankenJeep stories, you know that I no longer work in the oilfield. Not a big deal, as I am much happier these days, and I am now working with a really cool dude named Jack Reigelsperger. He has sort of taken me under his wing, teaching me the ways of custom car building and this has been good on multiple fronts – I am happy with my job again, I get to work with really cool cars, I am learning new things every day I am working, and I have been given a huge hookup when it comes to obtaining auto parts.
Jack hooked me up when we started wheeling and dealing over a project he had sitting in the yard. He had figured out a bolt on kit to put a 5.9L Cummins engine into a square body Chevy truck (1973-1991). He happened to have an ‘88 Suburban that was converted over and we got to talking about it, then we talked about wheelbase measurements. It turned out that the Suburban had a 131.5” wheelbase; Hyde has a 131” even. I already knew that the frame rails were close, as Chris ended up using the flatbed from my J20 to put on his CUCV and it bolted right up…
Do you see where I am going with this yet?
Let me run you through it again:
- I have an untrustworthy Jeep J20 with a clean body
- I have access to a Cummins powered square body with measurements similar to my J20
- I know a guy that has the knowledge, means, and desire to help marry the two
All of this adds up to one thing – a twin turbo Cummins powered Hyde!
Oh, did I forget to mention that? Yes, not one but TWO turbos!! We figure we should net around 600hp and 1400ftlbs of torque, making for a very fun 4×4.
Last time I was here, I mentioned that I drove down to Tucson to get a lift kit from Tad, and that I may be getting power doors. That was all true, I still have the lift kit (uninstalled, but I will explain that a bit later) and I did get power doors. I bought two power doors and a dashboard while I was in Amarillo. I managed to stuff all of that into the parts runner and drove it to Ft. Hood, TX and then home.
I was going to install the lift and the doors when I had an overheating issue sneak up on me. Now that I was done making it photo ready, I was driving it more, and I found out that the truck has no issues idling, but when I put it in gear and drove it, the radiator would heat the engine to temperatures I did not approve of.
I checked the oil/water mixes, and they remained separate, so that pretty much ruled out a blown head gasket. Phew! I know Chris would not let me live that down if I blew another head gasket.
I witnessed the radiator flow, and it drained as fast as the garden hose could fill it. I checked the water pump, which looked new and flowed through just as well. I replaced the thermostat, then removed it. I bought a new lower radiator hose and then stole an old Chevy hose spring and shoved it inside, hoping that would help out. Nothing. All of this brought me to the conclusion that… I have no idea why my radiator is pressurizing and spitting out the coolant!
It was nearing my time to get back to work, so I turned it over to the professionals. I took it to Craig, at KNI Automotive and let him have a looksee at it while I was at work. I bought a head gasket set and a new radiator for it. You never know, and it is better to be over prepared than to be underprepared. Off went the truck to the doctor, and off I went to work.
[SKIP AHEAD THREE WEEKS]
I got home and called Craig.
“How is the truck?” I asked.
“It does not overheat, but it runs like shit.” he said.
I’ll take it! I test drove it before taking it home and sure enough, it no longer overheats. Craig was right, it did not run very well at all. Do not twist it; the truck went from A to B and back, it was just extremely cold blooded – Arctic cold blooded. And due to the lack of weight in the rear it was very squirrely. It definitely needed a proper tune up, and something had to be done about the weight distribution.
The overheating issue was a bad radiator. Evidently, there was enough flow for it to work at idle, but once the truck was in gear and on the move, the radiator could not keep up. Craig replaced the radiator and the thermostat housing, putting in a new thermostat. Seeing as he did not need the gasket kit, I took it back to the parts store and returned it for the parts needed for a tune up and an oil change.
I tuned it up, changed the oil, and also installed a proper set of eyes for a Jeep. That is correct, while I was in Texas, I caught up with Cherokee Jim and he had a razor grille for me. Round headlights at last!
After the tune up was complete and the oil was changed, I took the truck on another test drive. It drove much better this time. It still needs a proper carburetor tune up, and it is leaking oil pretty severely, but it drives much better now.
What was to be done about the lack of weight in the rear, you ask?
When you are a gearhead for long enough, you start to know people. Good people. Sometimes these good people have bad situations that fall to your advantage. Take Ziggy for example, Christian’s dad. Ziggy likes to go to the government auctions and get military trucks and trailers. One of his trailers did not pan out as a trailer, so I offered to take it off his hands and, well just look for yourself…
– The Truck –
– The Trailer –
Getting the truck ready for its new bed –
I even got the teenager to help out!
Placing the bed onto the truck –
Spotting potential problem areas –
After cutting off the lip and hooks of the trailer and relocating the breather hose, we got a direct fit –
I did some simple, yet highly effective fabbing and relocating –
This went from reflector to gas filler –
End result –
. . .
Your truck looks bad ass, but did you address the carburetor problem? No.
Did you fix the oil leaks? No.
As I mentioned, those were problems that I could temporarily deal with, as this truck does not yet see a lot of drive time and it is still under construction. I am still getting it there, and seeing as I have work coming up, I will again drop off the truck to Craig to have him address those issues.
I am sure you are aware of my other Jeep build, FrankenJeep
If you follow it, or have even read it, you understand the things of that nature seem to take a bit longer for me. Not to say that I never get them done, but I do have a bit of an ADHD quality about me when some things are concerned. Good news is that Craig also is a fabricator. I have already spoken with him, and he has agreed to check out my front axle project for the hot rod. That means the little Jeep might see some attention here very soon, as I need the axle made before I can set the suspension. And now that I have a functioning truck, I can bring home the engine and the rear axle, making the hot rod closer to ready for more fab work. But all of this is for the other page.
This page is about a Jekyll and Hyde build of a truck.
What is in store for this truck next time around?
Oh boy, are we in for a treat here! You see, my buddy Cherokee Jim has a few tricks up his sleeve. Let us put it this way – the lift kit, that dash pad and my fenders are going to him.
Why, you ask? For trade.
First of all, I still owe him for the razor grille, but secondly, I am making partial trade on a set of stretch fenders, and these things are bad to the bone!
Now, this is not his fender. I believe this one is fiberglass and I know that his are metal, but it still gives you an idea of what he does.
For reference, this is where a normal FSJ fender sits.
This is one of his fenders. It is just a production picture, and not a finished product, but it also kind of shows you how he does it. These metal fender flares are removable and he takes them off, stretches them and welds them back into place, per customer’s specifications.
And if you need to see where my fenders sit, as a reference to my particular circumstances…
Haha! Remember, they are in the parts runner and will be going to Cherokee Jim as trade.
Why would anyone want those?
They are bad ass, of course! Plus, I can put bigger tires on the truck without lifting it, and that is a big thing for me right now, as I do not want to spend obscene amounts of money on this driving chassis.
But you already spent money on a lift kit, why not just install that and be normal?
You see, my plans are to get a Cummins Ram and do a body swap with it. The aftermarket support is better for the Ram, and not to mention that I will get better suspension out of it. Also, the diesel is already in the frame, and it will have matched components. This, opposed to trying to figure out how to put a bunch of diesel parts into a Jeep frame that was never built to handle that sort of torque.
I know it has been done before. There are plenty of Full Size Jeeps that have been converted, and with good results. But for my application, I see this as being the best and most effective route to convert my J20 to diesel.
All of this is still down the road, as I have yet to acquire a diesel Ram, so we will just have to stay tuned and wait to see how that all plays out later.
For now, we can keep watch for the next body mods that are to come shortly. To start off with, those include the stretch fenders and bigger tires. If I come across a rhino grille, I will be installing that and running a quad light set up too. I am also in the process of converting all lighting to LED. These are all quick modifications that show instant results, and these days, that is what we all want, right?
I will let you know how it all pans out next time.